Food Science and Preservation
The Korean Society of Food Preservation
Research Article

Determination of cholesterol content in processed foods commonly consumed in Korea using a validated GC-FID method, with GC-MS confirmation of trace cholesterol

Marie Faustine Niyomubyeyi1,2https://orcid.org/0009-0009-7068-6769, Sunyoung Lim1,2https://orcid.org/0009-0000-8220-0847, Jeung-Hee Lee3https://orcid.org/0000-0002-4224-771X, Youngmin Choi4https://orcid.org/0000-0002-8633-4671, Jung-Ah Shin1,2,*https://orcid.org/0000-0002-0194-1457
1Department of Marine Convergence Science, Kangwon National University, Gangneung 25457, Korea
2Department of Food Processing and Distribution, Kangwon National University, Gangneung 25457, Korea
3Department of Food and Nutrition, Daegu University, Gyeongsan 38453, Korea
4Food and Nutrition Research Division, National Institute of Crop and Food Sciences, Wanju 55365, Korea
*Corresponding author Jung-Ah Shin, Tel: +82-33-640-2339, E-mail: jashin@kangwon.ac.kr

Citation: Niyomubyeyi MF, Lim S, Lee JH, Choi Y, Shin JA. Determination of cholesterol content in processed foods commonly consumed in Korea using a validated GC-FID method, with GC-MS confirmation of trace cholesterol. Food Sci. Preserv., 33(5), 894-906 (2026)

Copyright © The Korean Society of Food Preservation. This is an Open Access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/4.0) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.

Received: Aug 06, 2026; Revised: Sep 21, 2026; Accepted: Sep 24, 2026

Published Online: Oct 31, 2026

Abstract

Cholesterol content must be declared on processed-food labels in Korea, but validated values are unavailable for many products. We determined the cholesterol content of 43 processed foods commonly consumed in Korea, including 22 seafood products, 5 meat products, and 16 sauce and spice products, using direct saponification, trimethylsilyl (TMS) derivatization, and gas chromatography with flame ionization detection (GC-FID). The method was validated in accordance with AOAC single-laboratory guidelines. Validation demonstrated acceptable analytical performance [recovery 101.38%, relative standard deviation (RSD) 4.00%, z-score 0.45 against SRM 1546a; R2 = 0.9994; limit of detection (LOD) 0.09 and limit of quantification (LOQ) 0.43 mg/100 g]. Cholesterol content in seafood products ranged from 7.64 to 339.22 mg/100 g, with the highest value observed in smoked squid (339.22 mg/100 g), corresponding to 113% of the recommended daily limit of 300 mg/day. In meat products, cholesterol content ranged from 6.39 to 46.07 mg/100 g, with the highest value observed in roasted spam ham. Among sauces and spices, the highest cholesterol content was 34.77 mg/100 g in cheese-flavored seasoning. Fish cutlet showed the greatest cooking-related increase in cholesterol content per 100 g, with increases of 34.97% after oil-frying and 65.55% after air-frying, mainly attributable to moisture loss. Cholesterol was not detected in several plant-based products, whereas onion powder contained 10.11 mg/100 g dry weight; gas chromatography-mass spectrometry (GC-MS) confirmed this trace peak as cholesterol (characteristic ions at m/z 458, 368, 329, and 129). These data provide additional values for the Korean Food Composition Database for use in nutrition labeling and dietary assessment.

Keywords: cholesterol; processed foods; TMS derivatization; gas chromatography; method validation

1. Introduction

Cholesterol is a sterol found naturally in foods of animal origin and performs essential physiological functions as a structural component of cell membranes and a precursor of bile acids, steroid hormones, and vitamin D3 (Albuquerque et al., 2016; Andersen, 2018; Chen et al., 2015; Li et al., 2019). Despite these roles, excessive dietary cholesterol intake has been associated with elevated serum cholesterol concentrations and an increased risk of cardiovascular diseases such as hyperlipidemia and atherosclerosis (Duan et al., 2019; Kim et al., 2011; López-Puebla et al., 2025; Ndhlala et al., 2023). Accordingly, the Dietary Reference Intakes for Koreans recommend that adults aged 19 years and older limit cholesterol intake to less than 300 mg/day (MOHW, 2025). Reliable data on the cholesterol content of commonly consumed foods are therefore essential for dietary assessment, nutrition labeling, and public health research.

In Korea, the consumption of processed foods has risen steadily with changing dietary patterns, increasing the dietary contribution of processed animal-derived products and their constituent ingredients (Jung et al., 2022). Many such products, including processed seafood, meat products, sauces, and spices, are widely consumed but remain poorly characterized for cholesterol content in current food composition databases. Because cholesterol is one of the nutrients required to be declared on processed food labels in Korea (Jung et al., 2022), the lack of validated analytical values for these product categories creates a practical gap in regulatory compliance and consumer information. Cholesterol content varies widely among processed foods depending on food source, species, ingredients, tissue composition, and processing conditions. Previous studies have reported values of 6.50-78.40 mg/100 g in raw marine fish (Ozogul et al., 2015), 131.08 mg/100 g in shrimp pancake, and 247.92 mg/100 g in seasoned pollock roe (Ahn and Shin, 2023). In meat products, cholesterol contents of 30-34 mg/100 g in Iberian dry-cured ham (Petrón et al., 2003) and 44.34-52.66 mg/100 g in raw and cooked pork loin (Min et al., 2016) have been reported. In contrast, cholesterol data for commercially available sauces and seasonings remain limited, highlighting the need for systematic analysis of these food categories using a validated method.

Several analytical techniques have been used to determine cholesterol in foods, principally gas chromatography (GC) (Albuquerque et al., 2016; Chen et al., 2015; Duan et al., 2019; Kim et al., 2011) and high-performance liquid chromatography (HPLC) (Azrina et al., 2015; Daneshfar et al., 2009; Domínguez et al., 2018; Kolarič and Šimko, 2020). Among these, direct saponification followed by trimethylsilyl (TMS) derivatization and GC analysis is widely regarded as the reference procedure (Chen et al., 2015; Dinh et al., 2012), and AOAC Official Method 994.10 remains the only officially validated method specifically developed for cholesterol determination in foods by GC with flame ionization detection (FID) (AOAC, 2000; Domínguez et al., 2018). However, the accurate quantification of cholesterol in compositionally diverse processed foods, particularly plant-based sauces and spices in which cholesterol occurs only at trace levels within complex matrices, remains analytically demanding and requires a method with demonstrated performance across such matrices.

The Korean Ministry of Food and Drug Safety (MFDS) has maintained the Korean Food Composition Database (FCDB) since 2009, providing a comprehensive source of nutritional information for dietary assessment, nutrition policy, and food labeling (Ahn and Shin, 2023; Sharmin et al., 2017); however, cholesterol values remain unavailable for many processed foods commonly consumed in Korea. Accordingly, this study aimed to determine the cholesterol content of 43 commonly consumed processed foods, including seafood, meat, and sauce and spice products, using gas chromatography with flame ionization detection (GC-FID) validated in accordance with AOAC single-laboratory validation guidelines and to provide reliable analytical data for the FCDB. Additionally, gas chromatography-mass spectrometry (GC-MS) was used to confirm the identity of trace cholesterol detected in selected spice products, thereby verifying the applicability of the analytical approach to complex food matrices.

2. Materials and methods

2.1. Chemicals and reagents

Reagent-grade ethanol, n-hexane, and ethyl acetate for cholesterol extraction were purchased from Samchun Chemicals Co., Ltd. (Seoul, Korea). Potassium hydroxide (KOH, 93.0% purity), pyrogallol (99.0% purity), and butylated hydroxytoluene (BHT, 99.5% purity) were purchased from Daejung Chemicals & Metals Co. (Siheung, Korea), and sodium chloride (NaCl) was purchased from Showa Chemical Co. (Shanghai, China). Hexamethyldisilazane (HMDS, ≥ 99.0% purity), chlorotrimethylsilane (TMS, ≥ 99.0% purity), and high-purity cholesterol and 5α-cholestane standards were purchased from Sigma-Aldrich Co. (St. Louis, MO, USA), and N,N-dimethylformamide (DMF, 99.5% purity) was purchased from Tokyo Chemical Industry Co. (Tokyo, Japan). Standard reference material (SRM 1546a) was purchased from the National Institute of Standards and Technology (NIST, Gaithersburg, MD, USA).

2.2. Sample preparation

Forty-three processed food products, including seafood products (n = 22), meat products (n = 5), and sauces and spices (n = 16), were provided by the Rural Development Administration (RDA, Jeonju, Korea). According to RDA sampling records, the products were collected or purchased in 2023-2024. All samples except onion powder were homogenized and analyzed without additional drying. The onion powder sample subjected to GC-MS analysis was confirmed by the product label to contain 100% dehydrated onion, with no other declared ingredients. The samples were stored at −27°C until analysis. Before analysis, the freeze-dried samples were equilibrated to room temperature for at least 20 min, thoroughly homogenized to ensure uniformity, and then subjected to cholesterol extraction.

2.3. Direct saponification and extraction

Samples and the standard reference material were prepared for cholesterol analysis using direct saponification and solvent extraction as described by Ahn and Shin (2023). Approximately 2-3 g of the well-homogenized sample was accurately weighed into an extraction tube, followed by 3 mL of distilled water and 10 mL of 6% pyrogallol in ethanol. The mixture was vortexed for 2 min, flushed with nitrogen for 1 min, and sonicated at 25°C for 10 min. Then, 8 mL of 60% KOH solution was added to the mixture. The mixture was vortexed for 1 min, followed by nitrogen flushing for 1 min. Saponification was performed in a shaking water bath at 75°C and 100 rpm for 1 h. After saponification, the mixture was cooled to room temperature. Then, 20 mL of 2% NaCl solution (in distilled water) and 10 mL of extraction solvent (hexane/ethyl acetate, 85:15, v/v, containing 0.01% BHT) were added, and the mixture was vortexed vigorously for 2 min. The upper unsaponified layer was passed through an anhydrous sodium sulfate (Na2SO4) column into a 50 mL volumetric flask. The extraction was repeated four times, and the combined extracts were brought to volume with the extraction solvent. A 12 mL aliquot was evaporated to dryness under a stream of nitrogen, redissolved in 3 mL of acetone, and evaporated again under nitrogen.

2.4. Cholesterol derivatization

The dried residue was dissolved in 3 mL of DMF for derivatization. A 1 mL aliquot of each solution was derivatized with 0.2 mL of HMDS and 0.1 mL of TMS, vortexed for 30 s, and left at room temperature for 15 min. Then, 1 mL of internal standard solution (5α-cholestane, 0.1 mg/mL in n-heptane) and 10 mL of distilled water were added to terminate the reaction. The mixture was vortexed for 1 min, and the heptane layer was transferred through an anhydrous Na2SO4 column into a GC vial.

2.5. GC with FID

Cholesterol was identified and quantified using a YL 6500 GC system (6500GC, Young In Chromass, Anyang, Korea) equipped with an FID. Separation was achieved on an Agilent J&W Ultra 2 (5%-phenyl)-methylpolysiloxane column (25 m × 0.2 mm, 0.3 μm). The oven was held at 250°C for 5 min, then increased to 285°C at 10°C/min and held for 20 min. Nitrogen was used as the carrier gas at 1 mL/min; a 2 μL aliquot was injected with a split ratio of 20:1. The injector and detector temperatures were 280°C and 300°C, respectively. The retention times of the derivatized cholesterol standard and internal standard (5α-cholestane) were 14.64 min and 10.15 min, respectively. Cholesterol was quantified against the internal standard using the calibration curve. Representative GC chromatograms of the standards and a quality control sample (infant formula) are shown in Fig. 1.

kjfp-33-5-894-g1
Fig. 1. GC-FID chromatograms of a standard solution (A) and infant formula (B). Peak 1, 5α-cholestane (internal standard, IS); peak 2, cholesterol TMS derivative.
Download Original Figure
2.6. GC-MS

GC-MS analysis was performed on an Agilent 7890A gas chromatograph (Agilent Technologies, Santa Clara, CA, USA) coupled to an Agilent 5977 mass selective detector (MSD). Separation was achieved on an Agilent J&W HP-5 ms Ultra Inert (5%-phenyl)-methylpolysiloxane column (30 m × 0.25 mm, 0.25 μm). Helium was used as the carrier gas at a constant flow rate of 0.8 mL/min. The oven was held at 250°C for 5 min, then increased to 285°C at 10°C/min and held for 25 min (total run time, 33.5 min). A 2 μL aliquot of the derivatized extract was injected via autosampler at a split ratio of 5:1. The transfer line interface (thermal aux 1) and MSD transfer line (thermal aux 2) temperatures were 115°C and 280°C, respectively. The mass spectrometer was operated in electron ionization (EI) mode, with the ion source and quadrupole at 230°C and 150°C, respectively. Mass spectra were acquired in full-scan mode over an m/z range of 50-550. 5α-Cholestane was used as the internal standard. Because 5α-cholestane lacks a hydroxyl group, it does not form a trimethylsilyl (TMS) derivative and was detected as the underivatized compound. It was identified by its molecular ion at m/z 372 and by the characteristic ions at m/z 217 (base peak) and m/z 357 ([M-15]⁺). Cholesterol was analyzed as its TMS ether derivative (molecular weight 458). Its identity was confirmed based on three criteria: (i) the retention time matched that of the cholesterol standard; (ii) the characteristic ions at m/z 458 (molecular ion, [M]⁺), 368 ([M-90]⁺, loss of trimethylsilanol), 329 ([M-129]⁺), and 129 (the diagnostic ion of Δ⁵-3β-trimethylsilyloxy sterols) were observed together; and (iii) the relative intensities of these ions were consistent with those of the standard. The molecular ion at m/z 458 was used to distinguish cholesterol from co-eluting plant sterols (e.g., campesterol, stigmasterol, and β-sitosterol), whose TMS derivatives have different molecular ions.

2.7. Method validation

The method was validated in accordance with the AOAC single-laboratory validation guidelines to confirm that the GC-FID method provided reliable and reproducible cholesterol measurements (AOAC, 2002; Domínguez et al., 2018). Accuracy, precision, limit of detection (LOD), limit of quantification (LOQ), and linearity were evaluated. Accuracy and precision were assessed using SRM 1546a (NIST), using the certified value as the reference, and were expressed as recovery (%) and z-score:

Recovery  ( % ) = Cn Cm × 100
z −  Score  = ( Cn − Cm ) SD

where Cn is the analyzed cholesterol content (mg/100 g), Cm is the assigned (certified) value (mg/100 g), and SD is the standard deviation of the assigned value. According to AOAC (2002), recoveries of 80-115% with |z| ≤ 2 (at an analyte level of ~1 mg/100 g) are considered acceptable. LOD and LOQ were calculated from the calibration curve obtained in the linearity assessment:

LOD = 3.3 × SD   S
LOQ = 10 × SD   S

where SD is the standard deviation of the response (y-intercept) and S is the slope of the calibration curve. The resulting concentrations were converted to mg/100 g.

2.8. Analytical quality control

To ensure the quality of cholesterol measurements in food samples, in-house quality control (IHQC) samples consisting of infant formula and beef liver were analyzed with each batch of food samples and used to construct quality control (QC) charts (Fig. 2). Variations in analytical conditions, including instrument performance and sample preparation, can influence the measured cholesterol content over time. Therefore, QC charts were used to monitor analytical performance and to confirm that the method remained under statistical control throughout the analytical period. The QC charts were constructed using the mean and SD of the analytical results and included the upper and lower control lines (UCL and LCL) as well as the upper and lower action lines (UAL and LAL) (AOAC, 2002):

UCL and LCL  =  mean  ± ( 2 × SD )
UAL and LAL  =  mean  ± ( 3 × SD )
kjfp-33-5-894-g2
Fig. 2. Quality control charts of cholesterol analysis for infant formula (A) and beef liver (B). UAL, upper action line; UCL, upper control line; LAL, lower action line; LCL, lower control line.
Download Original Figure
2.9. Statistical analysis

Analytical measurements of food samples were performed in duplicate, and SRM 1546a was analyzed in triplicate. Data are presented as the mean ± SD. Statistical analysis was performed using IBM SPSS Statistics for Windows (Version 22.0; IBM Corp., Armonk, NY, USA). Differences among samples were assessed by one-way analysis of variance (ANOVA) followed by Tukey’s multiple comparison test; p < 0.05 was considered statistically significant.

3. Results and discussion

3.1. Method validation and analytical control of cholesterol analysis

The accuracy and precision of the method were evaluated using the recovery of SRM 1546a relative to its certified reference value, as shown in Table 1. According to the AOAC (2002) guidelines, at a concentration of 1 mg/100 g, a recovery within 80-115%, an RSD within 6%, and an absolute z-score of ≤ 2 are considered acceptable. The measured cholesterol content of SRM 1546a was 72.68 mg/100 g, corresponding to a recovery of 101.38%, an RSD of 4.00%, and a z-score of 0.45. These values fell within the AOAC acceptance ranges, indicating that the validated method provided accurate and reliable cholesterol measurements in processed food samples. As shown in Table 1, the calibration curve exhibited excellent linearity over the concentration range of 0.0015-0.2000 mg/mL, with the regression equation y = 10.033x + 0.0169 and a coefficient of determination (R2) of 0.9994. The LOD and LOQ of the method were 0.09 and 0.43 mg/100 g, respectively (Table 1). The LOQ was comparable to that reported by Islam and Chun (2024) and lower than that reported by Dinh et al. (2012) (LOD, 1.24 mg/100 g; LOQ, 3.76 mg/100 g) using GC-FID, indicating good analytical sensitivity. The analytical QC results are presented in Fig. 2. The mean cholesterol content in the infant formula was 48.55 mg/100 g, with upper and lower action lines (UAL and LAL) of 55.61 and 41.47 mg/100 g and upper and lower control lines (UCL and LCL) of 53.26 and 43.83 mg/100 g, respectively. For the beef liver, the mean cholesterol content was 676.31 mg/100 g, with UAL and LAL of 715.75 and 636.86 mg/100 g and UCL and LCL of 702.60 and 650.01 mg/100 g, respectively. Throughout the analytical period, the measured cholesterol contents of both IHQC samples remained within the established action lines, indicating that the analytical process remained under statistical control and supporting the reliability of the analytical results.

Table 1. Method validation (accuracy, precision, linearity, LOD, and LOQ) of the GC-FID system used for cholesterol determination
Parameter1) Value
Accuracy and precision (SRM 1546a, meat homogenate)
 Certified value (mg/100 g)2) 71.70 ± 2.203)
 Measured value (mg/100 g)4) 72.68 ± 2.91
 Recovery (%)5) 101.38
 RSD (%) 4.00
 z-Score6) 0.45
Linearity
 Regression equation y = 10.033x + 0.0169
 Coefficient of determination (R2) 0.9994
 LOD (mg/100 g) 0.09
 LOQ (mg/100 g) 0.43

RSD, relative standard deviation; LOD, limit of detection; LOQ, limit of quantification.

Certified value provided by NIST.

All values are mean ± SD (n = 3).

Measured value obtained by GC-FID in this study.

Recovery (%) = (measured value / certified value) × 100.

z-score = (measured value - certified value) / standard deviation of the certified values.

Download Excel Table
3.2. Cholesterol content of processed seafood products: Effects of cooking methods

The cholesterol contents of 22 processed seafood products (squid, flying fish roe, semi-dried pollock, pollock pancake, shrimp cutlet, fish cutlet, cockle, freshwater snail, sea mustard, mackerel, spanish mackerel, fermented oyster, fermented cutlass fish, and fermented anchovy) are presented in Table 2. In this study, RI (%) was calculated using the recommended daily cholesterol limit of 300 mg/day for adults (≥ 19 years) established in the Dietary Reference Intakes for Koreans (MOHW, 2025) as the reference value. The cholesterol content of the processed seafood products ranged from 7.64 ± 0.35 to 339.22 ± 16.72 mg/100 g, corresponding to RI values of 2.55-113.07%, with significant differences among samples (p < 0.05). The cholesterol content of seafood is influenced by various intrinsic and extrinsic factors, including diet, habitat, season, maturity, thermal conditions, and preservation methods (Jung et al., 2022; Ozogul et al., 2015; Shirai et al., 2006). Smoked squid exhibited the highest cholesterol content among all products tested (339.22 ± 16.72 mg/100 g, 113.07% RI), more than four times the value in oil-fried squid from the same species (79.07 ± 0.65 mg/100 g). Among the products examined, fish cutlet showed the greatest cooking-related increase in cholesterol content per 100 g, with increases of 65.55% after air-frying and 34.97% after oil-frying (Fig. 3). Shrimp cutlet also showed a moderate increase in cholesterol content per 100 g of sample, with increases of 29.08% after air-frying and 16.34% after oil-frying. Smaller increases were observed in flying fish roe, semi-dried pollock, and pollock pancake, although the magnitude of the change varied with the food matrix and cooking method. The higher cholesterol content per 100 g after cooking was likely attributable to moisture loss during thermal processing, which raises the relative cholesterol concentration on a weight basis (Lee et al., 2015). The cholesterol content of raw flying fish roe in the present study was 172.18 ± 8.24 mg/100 g and increased slightly to 178.76 ± 1.36 mg/100 g after steaming; both were considerably lower than the 430 mg/100 g reported for salted flying fish roe (tobiko) by Shirai et al. (2006). For semi-dried pollock, boiling significantly increased the cholesterol content on a 100 g basis from 85.87 ± 3.03 to 107.73 ± 0.97 mg/100 g, corresponding to a 25.51% increase. In contrast, pollock pancake showed no significant difference in cholesterol content between the frozen (143.85 ± 4.91 mg/100 g) and oil-fried (144.50 ± 1.87 mg/100 g) samples, indicating that oil-frying did not significantly affect the cholesterol level of this product. These values were also close to the 136.73 mg/100 g reported for raw pollock pancake in the Ministry of Food and Drug Safety database (MFDS, 2022a), likely reflecting consistent raw-material sourcing and standardized processing. In fish cutlet, the cholesterol content increased from 21.68 ± 0.29 mg/100 g in the raw sample to 29.26 ± 0.97 mg/100 g after oil-frying and 35.88 ± 1.52 mg/100 g after air-frying, corresponding to increases of 34.97% and 65.55%, respectively, when expressed per 100 g of sample. In shrimp cutlet, oil-frying and air-frying increased the cholesterol content by 16.34% and 29.08%, respectively, compared with the uncooked product. The cholesterol content of raw spanish mackerel (82.47 ± 1.92 mg/100 g) was higher than the values reported by Osman et al. (2001) and the USDA (2019) (41.1 and 76 mg/100 g, respectively), but lower than that reported by Azrina et al. (2015) (99.34 mg/100 g). Fermented oyster had a higher cholesterol content (48.59 ± 0.99 mg/100 g) than raw oyster, consistent with the raw-oyster value of 27.13 mg/100 g reported by Azrina et al. (2015). Cooking-induced changes in cholesterol content and the corresponding percentage variation (PV, %) for the seafood products are summarized in Fig. 3A. Differences among the raw and cooked samples of each product were evaluated by one-way ANOVA followed by Tukey’s test (p < 0.05), and the resulting significance groupings are indicated by different lowercase letters in both Table 2 and Fig. 3A. The increase in cholesterol content after cooking may be attributed mainly to moisture loss, which reduces sample weight while cholesterol is retained in the tissue, thereby increasing its content on a 100 g basis. In addition, heat-induced disruption of cellular membranes and tissue structures may facilitate the release and extraction of cholesterol from the food matrix, contributing to higher measured values in cooked samples (Lee et al., 2015; Ozogul et al., 2015).

Table 2. Cholesterol content and RI% of seafood products
Samples Cooking method Cholesterol content (mg/100 g fresh weight) RI (%)1) Percentage variation of cholesterol content (PV, %)2)
Squid Oil-fried 79.07 ± 0.653)fg4) 26.36 -
Smoked 339.22 ± 16.72a 113.07 -
Flying fish roe Raw 172.18 ± 8.24b 57.39 -
Steamed 178.76 ± 1.36b 59.59 3.96 ± 5.77
Semi-dried pollock Raw 85.87 ± 3.03f 28.62 -
Boiled 107.73 ± 0.97e 35.91 25.51 ± 3.30
Pollock pancake (Dongtaejeon) Raw 143.85 ± 4.91c 47.95 -
Oil-fried 144.50 ± 1.87c 48.17 0.49 ± 2.13
Shrimp cutlet Raw 35.70 ± 1.02hij 11.90 -
Oil-fried 41.56 ± 3.02hi 13.85 16.34 ± 5.15
Air-fried 46.06 ± 0.67h 15.35 29.08 ± 5.56
Fish cutlet Raw 21.68 ± 0.29j 7.23 -
Oil-fried 29.26 ± 0.97ij 9.75 34.97 ± 6.28
Air-fried 35.88 ± 1.52hij 11.96 65.55 ± 9.19
Cockles Canned 79.53 ± 2.12fg 26.51 -
Freshwater snail Raw 129.16 ± 0.30d 43.05 -
Sea mustard Oil-fried 7.64 ± 0.35k 2.55 -
Mackerel - 68.09 ± 3.64g 22.70 -
Spanish mackerel - 82.47 ± 1.92fg 27.49 -
Fermented oyster - 48.59 ± 0.99h 16.20 -
Fermented cutlass fish - 70.72 ± 0.11fg 23.57 -
Fermented anchovy - 84.67 ± 0.47f 28.22 -

RI (%) was calculated as the cholesterol content per 100 g of sample divided by the reference intake of 300 mg/day, multiplied by 100.

Percentage variation of cholesterol content (PV, %) = [(cholesterol content of cooked sample − cholesterol content of raw sample) / cholesterol content of raw sample] × 100.

All values are mean ± SD (n = 2).

a-kValues with different superscript letters within the same column differ significantly among the samples included in that table, as determined by one-way ANOVA followed by Tukey’s multiple-comparison test (p < 0.05).

Download Excel Table
kjfp-33-5-894-g3
Fig. 3. Changes in cholesterol content and percentage variation (PV, %) following cooking of seafood (A) and meat products (B). Cholesterol contents are expressed as mg/100 g fresh weight (FW). PV (%) was calculated as [(cholesterol content of cooked sample - cholesterol content of raw sample) / cholesterol content of raw sample] × 100. Bars represent the mean cholesterol content, and error bars indicate SD (n = 2). Different lowercase letters above the bars indicate significant differences among the raw and processed samples within each product, as determined by one-way ANOVA followed by Tukey’s multiple comparison test (p < 0.05). Bars sharing the same letter within a product are not significantly different.
Download Original Figure
3.3. Cholesterol content of processed meat products

Table 3 summarizes the cholesterol content of the processed meat products (spam ham and meat dumplings), which ranged from 6.39 ± 0.10 to 46.07 ± 0.47 mg/100 g. Among the analyzed products, roasted spam ham had the highest cholesterol content (46.07 ± 0.47 mg/100 g), whereas steamed meat dumplings had the lowest (6.39 ± 0.10 mg/100 g). The corresponding RI values ranged from 2.13 to 15.36%, based on the recommended daily cholesterol limit of 300 mg/day. Compared with raw spam ham, the cholesterol content per 100 g increased by 14.15% after roasting and by 3.43% after air-frying. The observed values were comparable to those reported for cooked ham by Souza and Silva (2006) (33.33-46.53 mg/100 g), but higher than those for dry-cured ham (30-34 mg/100 g) reported by Petrón et al. (2003). Similar cooking-related increases in cholesterol content have been reported in meat products. Lee et al. (2015) observed higher cholesterol contents in chicken meat after roasting, frying, and steaming and attributed these changes mainly to moisture loss and thermal disruption of cellular membranes. Bragagnolo and Rodriguez-Amaya (2003) also reported higher cholesterol contents in grilled Longissimus dorsi beef (67-70 mg/100 g) than in raw samples (40-43 mg/100 g), primarily as a result of moisture loss during grilling. Likewise, Min et al. (2016) reported an increase in cholesterol content in pan-roasted pork loin from 48.85 to 52.66 mg/100 g. In meat dumplings, the difference in cholesterol content per 100 g of sample between the raw and steamed samples was minimal. The changes in cholesterol content and PV (%) for the meat products after cooking are presented in Fig. 3B. Cholesterol content increased from 40.37 to 46.07 mg/100 g after roasting and to 41.73 mg/100 g after air-frying (Table 3). Within-product comparisons showed that the increase was significant only after roasting (p < 0.05), whereas no significant differences were observed between raw and air-fried ham or between raw and steamed meat dumplings (p > 0.05; Fig. 3B).

Table 3. Cholesterol content of meat products under different cooking methods
Samples Cooking method Cholesterol content (mg/100 g fresh weight) RI (%)1) Percentage variation of cholesterol content (PV, %)2)
Spam ham Raw 40.37 ± 0.863)c4) 13.46 -
Roasted 46.07 ± 0.47a 15.36 14.15 ± 2.21
Air-fried 41.73 ± 0.74b 13.91 3.43 ± 3.92
Meat dumplings Raw 6.53 ± 0.21d 2.18 -
Steamed 6.39 ± 0.10d 2.13 −2.11 ± 4.61

RI (%) was calculated based on the recommended daily cholesterol limit of 300 mg/day.

Percentage variation of cholesterol content (PV, %) = [(cholesterol content of cooked sample - cholesterol content of raw sample) / cholesterol content of raw sample] × 100.

All values are mean ± SD (n = 2).

a-dValues with different superscript letters within the same column indicate significant differences among groups as determined by Tukey’s multiple comparison test at p < 0.05.

Download Excel Table
3.4. Cholesterol content of sauce and spice products

Cholesterol contents were determined in 16 sauce and spice products (tangsuyuk sauce, whole-grain mustard, clam flavor seasoning powder, onion-flavored seasoning, cheese-flavored seasoning, onion powder, oriental dressing, doubanjiang sauce, mala sauce, sriracha sauce, Pad Thai sauce, fish sauce, anchovy sauce, custard powder, cooked custard, and custard cream) and are summarized in Table 4. Among the analyzed products, cheese-flavored seasoning had the highest cholesterol content (34.77 ± 0.07 mg/100 g), followed by onion-flavored seasoning (25.88 ± 0.17 mg/100 g) and anchovy sauce (19.51 ± 1.47 mg/100 g). In contrast, cholesterol was not detected in tangsuyuk sauce, whole-grain mustard, doubanjiang sauce, mala sauce, sriracha sauce, Pad Thai sauce, fish sauce, custard powder, cooked custard, or custard cream (Table 4). These results are consistent with previous reports of no detectable cholesterol in doubanjiang (RDA, 2023), sriracha sauce (MFDS, 2022b), custard powder (USDA, 2017), and whole-grain mustard (USDA, 2019). The onion powder analyzed in this study consisted solely of dehydrated onion, with no other declared ingredients. Therefore, the cholesterol detected at 10.11 ± 0.35 mg/100 g was not attributable to added animal-derived ingredients or cholesterol-containing additives. This finding is consistent with recent evidence reported by Prayitno et al. (2025) of cholesterol occurrence in the genus Allium, although the concentration observed in the present study was lower than the 23.4 mg/100 g dry weight reported for dehydrated onion by LC-APCI-MS/MS. The identity of the trace cholesterol peak in onion powder was further confirmed by GC-MS. In the total ion chromatogram, a minor peak was observed at a retention time of 14.269 min (Fig. 4A), and its EI mass spectrum (Fig. 4B) showed the characteristic ions of the cholesterol TMS derivative, including the molecular ion at m/z 458 and the fragment ions at m/z 368, 329, and 129. A head-to-tail comparison with the reference spectrum of the cholesterol TMS derivative (Fig. 4C) showed close agreement in the m/z values and relative intensities of these ions, confirming that the peak corresponded to cholesterol.

Table 4. Cholesterol content and RI% of sauces and spices
Samples Cholesterol content (mg/100 g fresh weight) RI (%)1)
Tangsuyuk sauce ND2) ND
Whole-grain mustard ND ND
Clam flavor seasoning powder 4.50 ± 0.173)f4) 1.50
Onion-flavored seasoning 25.88 ± 0.17b 8.63
Cheese-flavored seasoning 34.77 ± 0.07a 11.59
Onion powder5) 10.11 ± 0.35d 3.37
Oriental dressing 8.05 ± 0.18e 2.68
Doubanjiang sauce ND ND
Mala sauce ND ND
Sriracha sauce ND ND
Pad Thai sauce ND ND
Fish sauce ND ND
Anchovy sauce (Meljeot sauce) 19.51 ± 1.47c 6.50
Custard, powder ND ND
Custard, cooked ND ND
Custard cream ND ND

RI (%) was calculated as the cholesterol content per 100 g of sample divided by the reference intake of 300 mg/day, multiplied by 100. For onion powder, RI (%) is based on 100 g dry weight.

ND, not detected.

All values are mean ± SD (n = 2).

a-fValues with different superscript letters within the same column differ significantly among the samples included in that table, as determined by one-way ANOVA followed by Tukey’s multiple-comparison test (p < 0.05).

Onion powder was a commercial product consisting of 100% dehydrated onion, and its cholesterol content is expressed as mg/100 g dry weight. Values for all other samples are expressed on a fresh weight basis.

Download Excel Table
kjfp-33-5-894-g4
Fig. 4. GC-MS identification of cholesterol in onion powder. (A), Total ion chromatogram; (B), EI mass spectrum of the peak at 14.269 min (peak 2); (C), head-to-tail comparison with the cholesterol TMS derivative reference spectrum. Peak 1, 5α-cholestane (internal standard, RT = 10.04 min); Peak 2, cholesterol TMS derivative (RT = 14.269 min).
Download Original Figure

4. Conclusions

In this study, cholesterol content was determined in 43 processed foods commonly consumed in Korea using a validated GC-FID method. The validated method showed a coefficient of determination (R2) of 0.9994, a recovery of 101.38%, an RSD of 4.00%, and LOD and LOQ values of 0.09 and 0.43 mg/100 g, respectively. Cholesterol content ranged from 7.64 to 339.22 mg/100 g in seafood products and from 6.39 to 46.07 mg/100 g in meat products, and the highest value among sauces and spices was 34.77 mg/100 g in cheese-flavored seasoning. Smoked squid had the highest cholesterol content among all analyzed samples. Cooking altered cholesterol content per 100 g in several products, with fish cutlet showing increases of 34.97% after oil-frying and 65.55% after air-frying relative to the uncooked sample. Cholesterol was also detected at a low concentration in onion powder, consistent with recent reports of cholesterol occurrence in selected Allium species. These results provide validated cholesterol composition data for processed foods and indicate that cholesterol content varies according to food category and cooking method. The data may be useful for updating the Korean Food Composition Database and for dietary intake assessment and nutrition labeling.

Acknowledgements

None.

Conflict of interests

Jeung-Hee Lee has served as the Editor-in-Chief of Food Science and Preservation since 2026 but was not involved in the review process for this manuscript. Otherwise, no relevant conflicts of interest have been reported.

Author contributions

Conceptualization: Shin JA. Methodology: Niyomubyeyi MF, Lim S, Lee JH, Choi Y, Shin JA. Formal analysis: Niyomubyeyi MF, Lim S. Validation: Lee JH, Choi Y, Shin JA. Writing - original draft: Niyomubyeyi MF, Lim S, Shin JA. Writing - review & editing: Shin JA.

Ethics approval

This article does not require IRB/IACUC approval because there are no human and animal participants.

Declaration of generative AI

No AI tools were used in this article.

Funding

This study was carried out with the support of “Cooperative Research Program for Agriculture Science and Technology Development (Project No. RS-2023-00220743)” Rural Development Administration, Republic of Korea.

ORCID

Marie Faustine Niyomubyeyi (First author) https://orcid.org/0009-0009-7068-6769

Sunyoung Lim https://orcid.org/0009-0000-8220-0847

Jeung-Hee Lee https://orcid.org/0000-0002-4224-771X

Youngmin Choi https://orcid.org/0000-0002-8633-4671

Jung-Ah Shin (Corresponding author) https://orcid.org/0000-0002-0194-1457

References

1.

Ahn TY, Shin JA. Analysis of fat-soluble nutrients (tocopherol, retinol, β-carotene, cholesterol, and fatty acids) in seafood restaurant foods commonly consumed in Korea. J Korean Soc Food Sci Nutr. 52:162-177 2023;

2.

Albuquerque TG, Oliveira MBPP, Sanches-Silva A, Costa HS. Cholesterol determination in foods: Comparison between high-performance and ultra-high-performance liquid chromatography. Food Chem. 193:18-25 2016;

3.

Andersen CJ. Impact of dietary cholesterol on the pathophysiology of infectious and autoimmune disease. Nutrients. 10:764 2018;

4.

AOAC. AOAC Guidelines for Single Laboratory Validation of Chemical Methods for Dietary Supplements and Botanicals.Association of Official Analytical Chemists International. Gaithersburg, MD, USA: p. 12-31 2002;

5.

AOAC. Official method 994.10. cholesterol in foods: Direct saponification-gas chromatographic method. Official Methods of Analysis of AOAC International. AOAC InternationalGaithersburg, MD, USA 2000

6.

Azrina A, Abd Aziz N, Khoo HE, Amin I, Al-Sheraji SH, Muhammad Rizal R. Cholesterol and alpha-tocopherol contents of fish and other seafood from the Straits of Malacca. Int Food Res J. 22:1494-1500 2015;

7.

Bragagnolo N, Rodriguez-Amaya DB. New data on the total lipid, cholesterol and fatty acid composition of raw and grilled beef longissimus dorsi. Arch Latinoam Nutr. 53:312-319 2003;

8.

Chen YZ, Kao SY, Jian HC, Yu YM, Li JY, Wang WH, Tsai CW. Determination of cholesterol and four phytosterols in foods without derivatization by gas chromatography-tandem mass spectrometry. J Food Drug Anal. 23:636-644 2015;

9.

Daneshfar A, Khezeli T, Lotfi HJ. Determination of cholesterol in food samples using dispersive liquid-liquid microextraction followed by HPLC-UV. J Chromatogr B. 877:456-460 2009;

10.

Dinh TTN, Thompson LD, Galyean ML, Brooks JCL, Boylan ML. Determination of total cholesterol in meat and poultry by gas chromatography: Single-laboratory validation. J AOAC Int. 95:472-488 2012;

11.

Domínguez R, Barba FJ, Centeno JA, Putnik P, Alpas H, Lorenzo JM. Simple and rapid method for the simultaneous determination of cholesterol and retinol in meat using normal-phase HPLC technique. Food Anal Methods. 11:319-326 2018;

12.

Duan BB, Shin JA, Lee KT. The contents of β-carotene and cholesterol in selected types of agricultural and processed foods in Korea. Korean J Agric Sci. 46:315-322 2019;

13.

Islam MA, Chun J. Effects of derivatization coupled with GC-FID analysis of cholesterol in some bakery products. Heliyon. 10:e30596 2024;

14.

Jung SH, Jeong YR, Shin HY, Kim YK, Yoon NY. Improvement and verification of a cholesterol analytical method to analyze cholesterol content in seafood. Korean J Fish Aquat Sci. 55:218-223 2022;

15.

Kim JM, Park JM, Yoon T, Leem D, Yoon C, Jeong J, Jeong IS, Kwak BM, Ahn JH. Development of an analysis method for cholesterol in infant formula by direct saponification. Korean J Food Sci Anim Resour. 31:944-951 2011;

16.

Kolarič L, Šimko P. Determination of cholesterol content in butter by HPLC: Up-to-date optimization and in-house validation using reference materials. Foods. 9:1378 2020;

17.

Lee JH, Lee HN, Shin JA, Chun JY, Lee J, Lee KT. Content of fat-soluble nutrients (cholesterol, retinol, and α-tocopherol) in different parts of poultry meats according to cooking method. J Korean Soc Food Sci Nutr. 44:234-241 2015;

18.

Li LH, Dutkiewicz EP, Huang YC, Zhou HB, Hsu CC. Analytical methods for cholesterol quantification. J Food Drug Anal. 27:375-386 2019;

19.

López-Puebla S, Arias-Santé MF, Romero J, Costa de Camargo A, Rincón-Cervera MÁ. Analysis of fatty acid profile, α-tocopherol, squalene and cholesterol content in edible parts and by-products of South Pacific wild fishes. Mar Drugs. 23:104 2025;

22.

Min JS, Khan MI, Lee SO, Yim DG, Seol KH, Lee M, Jo C. Impact of cooking, storage, and reheating conditions on the formation of cholesterol oxidation products in pork loin. Korean J Food Sci Anim Resour. 36:23-28 2016;

23.

MOHW. Dietary Reference Intakes for Koreans: Energy and Macronutrients (KDRIs).Ministry of Health and Welfare. Sejong, Korea: p. 211 2025;

24.

Ndhlala AR, Kavaz Yüksel A, Çelebi N, Doğan HÖ. A general review of methodologies used in the determination of cholesterol (C27H46O) levels in foods. Foods. 12:4424 2023;

25.

Osman H, Suriah AR, Law EC. Fatty acid composition and cholesterol content of selected marine fish in Malaysian waters. Food Chem. 73:55-60 2001;

26.

Ozogul F, Kuley E, Ozogul Y. Sterol content of fish, crustacea and mollusk: Effects of cooking methods. Int J Food Prop. 18:2026-2041 2015;

27.

Petrón MJ, García-Regueiro JA, Martín L, Muriel E, Antequera T. Identification and quantification of cholesterol and cholesterol oxidation products in different types of Iberian hams. J Agric Food Chem. 51:5786-5791 2003;

28.

Prayitno V, Kim HC, Cho EJ, Lee KT. Exploring cholesterol presence in Allium cepa and Allium fistulosum L. using LC-APCI-MS/MS. J Food Compos Anal. 147:108061 2025;

29.

RDA. Korea food composition table 10.3. Rural Development Administration. Available fromhttps://www.nics.go.kr/food/kfi/fct/fctFoodSrch/list?menuId=PS03563#Accessed [Apr. 06, 2023]. .

30.

Sharmin F, Jeong BG, Jung J, Quines V, Chun J. Cholesterol analysis of Korean eat-out foods for national food composition database. J Food Sci Technol. 54:1837-1849 2017;

31.

Shirai N, Higuchi T, Suzuki H. Analysis of lipid classes and fatty acid composition of salted fish roe food products: Ikura, Tarako, Tobiko, and Kazunoko. Food Chem. 94:61-67 2006;

32.

Souza VLF, Silva RSSF. Dietary vitamin E supplementation on cholesterol and cholesterol oxides of pig meat and cooked ham. Braz Arch Biol Technol. 49:197-205 2006;

33.

USDA. Food Data Central. United States Department of Agriculture. Available fromhttps://fdc.nal.usda.gov/food-details/468094/nutrientsAccessed [Jul. 14, 2023]. .

34.

USDA. Food Data Central. United States Department of Agriculture. Available fromhttps://fdc.nal.usda.gov/food-details/2403026/nutrientsAccessed [Sep. 24, 2023]. .